Stainless steel door cover wire edges are generally customized and rarely made on-site, as the current technical level of workers does not meet the inspection and evaluation standards, and there are no professional stainless steel construction operators on site.

在制作不銹鋼門套的時候,我們都是按門套基層的尺寸畫好加工圖,該折的部位廠家折好,采用膠或者玻璃膠粘貼,立面與頂面交接也不用焊接!

When making stainless steel door jambs, we always draw processing drawings according to the size of the base layer of the door jamb. The manufacturer folds the folded parts and uses universal adhesive or glass adhesive to paste them. There is no need to weld the connection between the facade and the top surface!

我們在以前做不銹鋼的時候碰到過處理不太好的情況,所以就采用豎向門套線通縫,門套橫向與豎向線條交接的地方采用橫縫磁豎縫的方法,后在縫隙處打膠。這種做法在工藝上要求不高,做起來方便,在45度角較接觀感達不到要求的情況下我覺得這樣做也是可以的。

We encountered poor treatment when making stainless steel in the past, so we used vertical door jamb line through seam. The intersection between the horizontal and vertical lines of the door jamb used transverse seam magnetic vertical seam method, and then applied glue at the gap. This method has low technical requirements and is convenient to use. I think it is also feasible when the appearance at a 45 degree angle cannot meet the requirements.

1.用沖擊電鉆在門四周大洞眼,并插入木楔。

1. Use an impact drill to drill large holes around the door and insert wooden wedges.

2.將15厘大芯板(或夾板)靠墻側進行防潮處理(刷光油2遍后在貼珍珠棉)。用釘槍校正固定后,再用鐵釘加固。門套線條打底用9厘夾板。打底夾板外側用實木線條收口。合頁位置加板襯固或封兩層15厘大芯板。

2. Moisture-proof treatment should be applied to the side of the 15 cm large core board (or plywood) against the wall (after applying two coats of varnish and then applying pearl cotton). After correcting and fixing with a nail gun, reinforce with iron nails. Use a 9mm plywood for the bottom of the door pocket line. Close the outer side of the base plywood with solid wood lines. Add a board lining or seal two layers of 15 cm large core board at the hinge position.

3.門套與門扇相合之處到進門邊的側面用9厘夾板做止口板,止口深度與門的厚度相同。

3. Use a 9mm plywood as a stop plate from the joint of the door pocket and the door leaf to the side of the entrance door, with the depth of the stop plate being the same as the thickness of the door.

4.面板用白乳膠涂勻后貼于打第大芯板及止口板上,并用不銹鋼蚊釘適當加固。

4. The panel should be evenly coated with white latex and applied to the largest core plate and mouth plate, and properly reinforced with stainless steel mosquito nails.

5.門套線條寬度一般為60mm—80mm.厚度8mm.

5. The width of the door pocket line is generally 60mm -80mm, and the thickness is 8mm

6.廚衛門套線條里側用不銹鋼(啞光)線條為宜。

6. It is advisable to use stainless steel (matte) lines on the inner side of the kitchen and bathroom door covers.

7.門套及門窗套垂直、水平誤差不超過2mm(2m以上不超過3mm)對角線誤差不超過3mm(2m以上不超過5mm).

7. The vertical and horizontal errors of the door and window covers shall not exceed 2mm (not exceeding 3mm for 2m and above), and the diagonal error shall not exceed 3mm (not exceeding 5mm for 2m and above)

8.門套兩側墻與門套之間距離在門套線條不能壓住接縫時,宜先用水泥砂漿掛鋼釘封平(用板定模灌漿)干燥后方可封板打第,在門套線條能壓住接縫時可用板封龍骨結構。

When the distance between the walls on both sides of the door jamb and the door jamb is such that the door jamb line cannot press the joint, it is advisable to first use cement mortar to hang steel nails for sealing (using plate fixed mold grouting) and dry before sealing the board. When the door jamb line can press the joint, the board can be used to seal the keel structure.

9.單面門套用9厘板打底(凸窗應注意窗簾位置)。其他與雙面門套同。入戶大門可封單邊實木線條門套。

9. Use a 9-centimeter board as the base for the single-sided door cover (pay attention to the position of the curtains for raised windows). Other items are the same as double-sided door jambs. The entrance door can be sealed with a single sided solid wood line door pocket.

10.窗套不宜包臺面,臺面用大理石鋪貼(防盜網宜在窗套面板封后制作)。單面門套:在原來有門的基礎上起裝飾作用,不起承受門的力量。

10. The window cover should not cover the countertop, and the countertop should be paved with marble (the anti-theft net should be made after the window cover panel is sealed). Single sided door jamb: It serves as a decoration on the basis of the original door and cannot withstand the force of the door.

本文由德州電梯不銹鋼包邊整理發布，您是不是對這些內容有所了解了呢?更多的內容請點擊：http://m.caiaiwo.cn我們會有更多精彩內容等你查看。

This article is organized and published by Texas Elevator Stainless Steel Edge. Do you have any understanding of these contents? For more information, please click on: http://m.caiaiwo.cn We will have more exciting content waiting for you to check out.